Maxpette Series Pipette Controller

MaxPette Pipette Controller

MaxPette Pipette Aid This revolutionary battery powered pipette controller works with glass and plastic pipettes in the 1 to 100 ml range. The MaxPette was designed with the user in mind. It has a lightweight handle with smooth push-buttons and ergonomically located switches.
· Works with pipettes from 1 ml to 100 ml
· High aspiration speed - 25 ml in 4 seconds
· Cordless work for up to 8 continuous hours
· Ergonomically designed

The aspiration speed can be set to high or low to adjust for the volume of the pipette and viscosity of the liquid. The suction can also be adjusted by the amount of pressure applied to the trigger button. Dispensing can be carried out by gravity or supported by the pump, which empties the pipette with a blow out step.
The MaxPette is protected from the entrance of liquids by both a PTFE filter and a safety valve. To protect samples from cross contamination, both the filter and pipette holder are easily exchanged and autoclaved.
When fully charged, the MaxPette can be used continuously for eight hours. When the low battery light is lit, the unit should be recharged. Should the charge run out while working with the pipette, simply attach the power supply and continue to use. The battery is protected against over charging by timing and thermal systems. The MaxPette is supplied with the power supply/charger and PTFE filter.
 






  MaxPette Pipette Controller

MaxPette Pipette Aid This revolutionary battery powered pipette controller works with glass and plastic pipettes in the 1 to 100 ml range. The MaxPette was designed with the user in mind. It has a lightweight handle with smooth push-buttons and ergonomically located switches.
· Works with pipettes from 1 ml to 100 ml
· High aspiration speed - 25 ml in 4 seconds
· Cordless work for up to 8 continuous hours
· Ergonomically designed

The aspiration speed can be set to high or low to adjust for the volume of the pipette and viscosity of the liquid. The suction can also be adjusted by the amount of pressure applied to the trigger button. Dispensing can be carried out by gravity or supported by the pump, which empties the pipette with a blow out step.
The MaxPette is protected from the entrance of liquids by both a PTFE filter and a safety valve. To protect samples from cross contamination, both the filter and pipette holder are easily exchanged and autoclaved.
When fully charged, the MaxPette can be used continuously for eight hours. When the low battery light is lit, the unit should be recharged. Should the charge run out while working with the pipette, simply attach the power supply and continue to use. The battery is protected against over charging by timing and thermal systems. The MaxPette is supplied with the power supply/charger and PTFE filter.
 






 

Continuous Waste Plastic Pyrolysis Plant

Pyrolysis Plant is used for recycling waste tire, waste plastic, waste rubber to fuel oil. According to the actual situation in every country and district, we developed different models of Batch Pyrolysis Plants for waste tires, rubber and plastic with daily capacity 25-40 tons.

Flow-chat of Continuous Waste Plastic Pyrolysis Plant

Advantages of Continuous Waste Plastic Pyrolysis Plant

 1.  Large daily capacity of 25 MT raw materials, and can work 24 hours without any stop for 15-20 days;

                  2.  Auto-loading, auto-discharging and oil coming out at the same time;

                  3.  Only need fuel for the beginning 2-3 hours, then the sync gas generates itself is enough to support heating, saving fuel cost;

                  4.  Low requirement on the raw materials, no need tiny granule, 5cm pieces acceptable for smooth running;

                 5.  High efficiency condensers, more oil output, good quality oil, easy to clean.

                 6.  Sync gas recycling system, fully burned after recycling and utilization, preventing pollution and saving fuel cost.

                7.  National patent smoke scrubber, can efficient remove the acid gas and dust of the smoke, environmental friendly to meet related national standards.

               8.  Easy to operate, need less manpower.

 

Technical Parameter of Continuous Waste Plastic Pyrolysis Plant

          

NO.	ITEM	Technical Parameter
1	Suitable Raw Materials	Small pieces of Waste tyre,rubber, waste plastic≤5cm
2	Operating Mode	Fully Continuous Operation
3	Structure	Horizontal Type Revolve
4	Loading and discharging	Fully Automatic Feeding and Discharging under High Temperature at Same Time
5	Capacity(24h)	8-20Mt
6	Work Pressure	Slightly Negative Pressure
7	Oil Yield of tyres	40%-45%
8	Reactor Rotational Speed	1R/M
9	Installation Power	110kw
10	Cooling Method	Cycle water
11	Type of Drive	Sprocket Wheel
12	Heating Method	Hot Air
13	Noise dB(A)	≤85
14	Main Reactor Weight (MT)	About 20Mt
15	Total Weight(MT)	About 45Mt
16	Installation Space Required	60m*20m
17	Manpower	2/shift
18	Shipment	5*40HC
19	Delivery time	≤70Days

 

 

 

 

 

 

Continuous Waste Plastic Pyrolysis Plant

Continuous Waste Plastic Pyrolysis Plant,Continuous Plastic Pyrolysis Plant,Plastic Pyrolysis Plant

Shangqiu Jinpeng Industrial Co., Ltd. , http://www.recyclingthewaste.com