STWYX15-225-900
Components:
- The uncoiler and its base
- Coil sheet guiding and adjusting equipment
- Film covered device
- Main roll forming system
- Post- Cutting device
- Hydraulic station
- PLC control System
- Support table
Material of Roll former system:
- Roller: High grade No. 45 forged steel, plated hard chromed on the surface of rollers with thickness 0.05mm.
- Active shaft material: High grade No. 45 carbon wrought steel at diameter 75mm.
- Cutting blade: Cr12 mould steel with quenched treatment.
Working flow:
Decoiling the sheet- - - Guiding the sheet- - - Covering the film- - - Roll forming- - - Measuring the length- - - Cutting the panel- - - Panels to the supporter.
Our machine's warranty time:
We offer 12 months quality grantee time starting from the date of delivery. When delivery, we will ship a set of wearing parts for free; Within the warranty period, maintenance of equipments and replacement of parts of equipment are charge-free.
After-sale service:
We offer sale after service for life. The machine will be inspected well in our workshop before delivery. We will send one technician to your factory to install the machine if you need extra installation, training service; The seller should arrange offer technical back-up and assign a technician people to the buyer's part.
| No. |       item | Parameter(all is subject to our final design) | |
| 1 Â |
Suitable raw material | Type | Common galvanized & pre-painted steel |
| Yield strength | 235MPa(or other high strength steel) | ||
| Thickness(mm) | 0.4-0.7 | ||
| width(mm) | According to final design | ||
| 2 | Manual uncoiler's capacity | Max.5tons | |
| 3 | Forming speed(m/min) | About 18-20m/min | |
| 4 | Main motor power(KW) | 7.5kw | |
| 5 | Hydraulic power(KW) | 3kw | |
| 6 | Forming roller groups | Around19-20 groups | |
| 7 | Raw material of forming roller | High quality No.45 steel | |
| 8 | Raw material of cutting blade | Cr12mould steel with quenched treatment | |
| 9 | controlling system | Mitsubishi PLC& converter | |
| 10 | Suitable industrial voltage |  According to your special requirement | |
| 11 | Machine dimensions(L*W*H) | 6.8m×1.8m×1.52m | |
| 12 | Machine weight | About 9-10tons | |
HWS Anti-corrosion Pipeline Heat Shrink Sleeve
Product Introduction:
HWS Anti-corrosion Pipeline Heat Shrink Sleeve is also known as heat shrink weld belt/Heat shrinkable weld sleeve (belt), made by irradiation cross-linked polyolefin base material and special sealing hot melt adhesive. WHR Three Layers Heat Shrink Sleeve For Anti-corrosion it has high mechanical strength, stable performance, aging resistance, anti chemical corrosion, sealing, strong adhesive strength, easy to operate, etc.
Product Application:
a) Pipeline Engineering Tubing Apply to petroleum, nature gas, chemical engineering, fuel gas and others project pipeline network for anti-corrosion of steel pipeline repaired and welded junction.And also apply to corrosion resistant coating for repairing the breakage.
b) Apply to 2PE, 3PE, FBE,PP,CTE anti-corrosion coating pipeline for anti-corrosion of welded junction and bend area.
Specification:
When using the heat shrink sleeves, first preheat the pipeline up to 55 degrees Celsius~60 degrees Celsius, and then wrap the joint belt around the treated pipeline with the heat shrink joint belt, make sure that the heat shrink joint belt lap width is more than 50mm, it will shrink at radial direction when the heat effects on it, at the same time the hot melt adhesive start to melt, fill and cover the surface of the pipeline, form continuous and close anti-corrosion system with original pipeline anti-corrosion coating.
Executive Standard: SY/T0413-2002 and SY/T4054-2003 and GB-T23257-2009.
Features & Benefits
a) excellent adhesion ability, adhesion range is wide: can adhere with steel, PE, epoxy coating, etc.
b) strong in corrosion resistance:can effectively block a variety of medium permeability and corrosion, aging resistance, environment stress cracking resistance, resistance to UV irradiation.
c) High mechanical strength: compression resistance, shock resistance, shear resistance.
d) Wide use range: can instruct at -25~35 degrees Celsius temperature range.
e) No volatilization, safety in use, can save energy, can protect environment
f) Long service life.
g) Shrink fast, easy to operate, simple to install.
h) low preheat temperature: when preheat -55~60 degrees Celsius, can install it to shrink.
Other size can customized according to customers' request.
Pipeline Engineering Tubing/sleeves
Pipeline Engineering Tubing,Pipeline Insulation Tape,Heat Shrink Polyethylene,Polyethylene Terephthalate Tubing
KEYUACE Materials Co., Ltd. , https://www.insulationtubing.com