The biggest drawback of bag filter is that it is necessary to replace the dust removal accessory - dust filter bag on a regular basis . In the past, due to the small variety of filter media, poor quality, and the lack of clearance of the bag technology, and other reasons of the dust removal system, the replacement cycle is relatively short, increasing. The operating costs and maintenance workload, inconvenience to users. Nowadays, China's filter materials have increased in variety and quality. The technology of sewing bags has also been greatly improved. The life of filter bags has been increased to more than two years, and even longer, meeting the requirements of users. Therefore, bag filter will develop rapidly in the next ten years. China's bag filter was mainly used in the Soviet Union in the 1950s. In the 1960s and 1970s, a few design and research institutes were mimicking pulsed, mechanically-rotated, reverse-blown flat bags of the United States, Japan, and other countries. The dust collector is based on the production of its own products. The current environmental standards require that the emission concentration must be below tens of milligrams per standard cubic meter. In terms of dust collection performance, only bag filter and electrostatic precipitator are generally sufficient. The electrostatic precipitator has low pressure loss during operation, and is used more often in the collection of excessive air volume in the power, steel, cement, and pulp industries. However, it has been replaced by bag filter in other uses of large air volume. Due to the large amount of bag filter used, the requirements for dust removal accessories have become more and more stringent. The quality of the dust removal accessories directly affects the use of the entire dust collector. Keda Environmental Protection Co., Ltd. specializes in the production of dust remover and supporting dust removal accessories in order to ensure the normal dust collection efficiency of the equipment.
Industry model, Kodak Environmental Protection, Hotline: 0317-8188867 For details, please login: http://
Food Machinery Precision Casting or food machinery investment casting, silica sol process. It is a casting process with little or no cutting.
Cast food machinery is an excellent process technology in the foundry industry. Its application is very extensive. Food machinery cast not only applies to the casting of various types and alloys, but also produces the dimensional accuracy of castings. The surface quality is higher than that of other casting methods, and even castings that are difficult to cast and which are difficult to cast have high temperature resistance and are not easily processed can be cast using investment casting.
In wax pattern process,we mix stearic acid and paraffin wax in wax pattern making,as you know,it is better than polyethylene,and the wax deformation is small.
In shell making,we adopt automatic sand-covering production line, which was invented under the guidance of our general manager.The indoor temperature was controlled by air-conditions,keeping the temperature at 24℃±1℃, which can make the castings much more stable,the internal tissues much more well-proportioned.
In shell hardening process,we use aluminium chloride to harden the shell.This can make the shell so hard that it can`t be distorted,at the same time the bug which the casting may have will be decreased.If there are letters or numbers in it,they will be much clearer.
In dewaxing process,about 95% of the castings suppliers adopt the original water dewaxing technics,but we using the advanced steam dewaxing technics,which we are very proud of. This can effectively avoid the air-hole and sand-hole, making the casting look much nicer.
In smelt process, we use middle frequency furnace, avoiding the emergence of the oxide; in molten steel control part, we use Germany-imported direct reading spectrometer machine, assuring its quality before the molten steel out of the furnace. During this process we use ERP production and management software to get the feedback information.
In shell-knock out process, we have special machines,which can decrease the hitting and knocking, easily made by manual shell knocking out.
In shot-blasting process, we have crawler-type and hanging shot-blasting machine, with steel shot 0.5-0.8, making the products smooth.Of course, if the customer wants it look much nicer, we also can carry out sand-blast treatment.
In heat treatment process, we use electric furnace, and adopt double-temperature control in order to heat the products equally. As a result, the products will have great metallurgical structure.
Our tolerance can reach at the grade of 5-7 according to our country`s tolerance standard.
In machining process,we have 12 CNC machining centers and some other machines, so we can make further machining if the customers need.
Precision Casting Of Food Machinery
Precision Casting Of Food Machinery,Investment Casts for Food Machinery,Food Machinery Investment Casts,Steel Casting for Food Machinery
Wei fang junlong precision casting Co.,Ltd , https://www.junlongcasting.com